Monday,15-December-2014

Opel Zafira - wiper & door problem

opel0.jpg opel1.jpg opel2.jpg
opel3.jpg opel4.jpg opel5.jpg
opel6.jpg

ENBG
Status:wipers once started never stop until you switch off the key.Problem was burned contact in the motor drive switch Rear door central lock: Broken wire in the rubber hose. Проблемът на този опел бе в това, че веднъж пуснати чистачките не спират докато не угасиш от контакт. Също така и задна дясна вратата не сработваше централното. Оказаха се проблемни пластинки на контактори в първия случай, и скъсан кабел във втория

Xsara 1.8 - Clutch fun

xsara1.jpg xsara2.jpg xsara3.jpg
xsara4.jpg xsara5.jpg xsara6.jpg
xsara7.jpg xsara8.jpg xsara9.jpg

One reason more to change your parts on time 061.gif

HEIDENHAIN iTNC 530 elipse

Within the manual you can find the original version of that idea, but i decide to reduce it and rewrite it. Few changes and you can get it to be produced in desired direction as left2right or right2left, inside or outside.

0  BEGIN PGM elipsa MM 
1  BLK FORM 0.1 Z  X-50  Y-50  Z-1
2  BLK FORM 0.2  X+50  Y+50  Z+1
3  TOOL CALL 3 Z S2500
4  ;------------------------------
5  Q1 = 20 ;elipse radius on X
6  Q2 = 10 ;elipse radius on Y
7  ;------------------------------
8  Q3 = Q108 + Q1 + 3
9  L  X+Q3  Y+0 R0 FMAX
10 L  Z-0.2 R0 FMAX
11 ;=============================
12 Q6 = 360
13 LBL 1
14 Q10 = ( Q1 + Q108 ) * COS Q6
15 Q11 = ( Q2 + Q108 ) * SIN Q6
16 L  X+Q10  Y+Q11 R0 F2000
17 Q6 = Q6 - 1
18 CALL LBL 1 REP360
19 L  Z+5 R0 FMAX M2
20 END PGM elipsa MM 

HEIDENHAIN iTNC 530 spiral outside to inside idea

That is my small idea for program, that produce horizontal XY spiral face clean. Analog to Cycle 5 but it work from outside to inside. Basic, that can use any tool to produce any diameter, but keep in mind that it is stupid to use 50mm to try spiral on 30mm surface. From other hand, with 20mm endmill is quite nice to produce 100mm cylinder face

Keep in mind also that depending of the tool size the start point can be very different. In example if we clean 65mm diameter with 20 or 10mm will give different start point and if there is jaw or something can be crashed or milled
[Read More…]

iTNC 530 - test sphere program

The idea behind is to make half sphere only with small piece of code. In theory, should be possible just changing Q1 or the sphere radius , and to make any size.. Well, there should be additional milling if the sphere radius is 300mm, because of the material need to be clean. And that is only.. program for fun test, and somehow it was working on the programming station but not on real machine simulation, because of 530 NC model family difference.

0  BEGIN PGM testsphere MM 
1  BLK FORM 0.1 Z  X-100  Y-100  Z-120
2  BLK FORM 0.2  X+100  Y+100  Z+2
3  FN 0: Q1 =+100
4  FN 0: Q2 =+2
5  TOOL CALL 20 Z S3500
6  ;D40-ENDMILL
7  Q3 = Q1 / Q2
8  LBL 1
9  L  Z+2 R0 FMAX M3
10 Q4 = Q1 + Q108 + 3
11 L  X+Q4  Z-Q2 R0 F5000
12 Q5 = SQRT ( ( Q1 ^ 2 ) - ( ( Q1 - Q2 ) ^ 2 ) ) + Q108 + 0.5
13 L  X+Q5  Y+0 R0
14 CC  X+0  Y+0
15 CP IPA+360 DR-
16 L IX+0.5 IZ+0.5 R0 F10000
17 Q2 = Q2 + 2
18 CALL LBL 1 REPQ3
19 L  Z+222 R0 FMAX
20 ;------
21 TOOL CALL 30 Z S6000
22 ;BALL-6MM
23 Q10 = Q1 + Q108 + 3
24 Q11 = Q108 + Q1
25 L  X+Q10  Y+0  Z+2 R0 FMAX M3
26 L  Z-Q11 R0 F3000
27 L  Z-Q108 R0 F1500
28 CC  X+0  Y+0
29 CP IPA+360 DR-
30 L  Z+5 R0 F5000
31 L  Z+2 R0 FMAX
32 LBL 2
33 L  X+Q11  Y+0  Z+2 R0 FMAX
34 Q12 = Q1 - 1
35 L  Z-Q12 R0 F5000
36 CC  X+0  Z+0
37 L  Z-Q11 R0 F2000
38 Q13 = Q108 + Q1
39 L  Z-Q13 R0 F1000
40 CR  X+0  Z+0 R+Q1 DR-
41 CR  X-Q11  Z-Q13 R+Q1 DR-
42 L  Z+2 R0 FMAX
43 CYCL DEF 10.0 ROTATION
44 CYCL DEF 10.1 IROT+1
45 CALL LBL 2 REP179
46 L  Z+200 R0 FMAX M2
47 END PGM testsphere MM 

Web design - Интернет страници

Agi Style BG - company site , html,css,js
agist1.jpg

Project Web Shop - company site - php, html, css, js, csv
china1.jpg china2.jpg china3.jpg china4.jpg
[Read More…]

Home design - Домашен дизайн

EN: The both designs was developed and produced by me.The paintings on full, the external wooden stuff partially.You can recognize from the drawings.
BG: И двата дизайна са мои, като на дървенията само оградата не е моя. Изпълнението обаче е.

home1.jpg home2.jpg
home3.jpg home4.jpg
home5.jpg home6.jpg
home7.jpg home8.jpg
home9.jpg

Shoes Andiamo 2013 - Обувки Андиамо 2013

EN: I take parts in one shoe design competition and that are some of the drawings.I did not won anything but was fun
BG: Това са част от предварителните скици за едно състезание в което опитах да участвам. Не спечелих нищо, но пък бе забавно

shoe1.jpgshoe2.jpgshoe3.jpg
[Read More…]

Car fun / Една авто идея

EN: that was my old car, and for it i prepare vector file that was vinyl cut, and then appear on my beauty
BG: това е бивша моя кола, за която подготвих белия стикер които бе изрязан от винил и поставен по-късно

graphic7.jpg

Few print out for friend - Няколко идеи за приятел

internet-print.jpgsluj-kanal-print.jpgtv-print.jpgvideo.jpg

EN:The story behind: it was one of that funny tasks.. to help friend. So here it was, my try. Now you can find them out on few windows in… 020.gif
BG:Историята: един приятел ме помоли за малко помощ. И това което виждате бе моят опит за идея. Която между другото може да видите на живо в…