Sunday, 4-June-2017
Passat 3B2 - messing with wires :)
EN
That time mate of mine call me to check over his car if we can find some solution about missing power to door welcome lights.
It seem that all positive voltage supply to door and cabin map lams are taken from comfort module, and ground taken either from door lock unit or control pin from the same comfort module.
[Read More…]
Sunday,28-May-2017
Xantia Estate Trunk Cover plastic ends/hooks [FIX]
EN
Hi there,
If you own Xantia Estate perhaps some day will get to the point where that damn plastic ends just broke. Well, option one is to pay 54e for pair and get from Citroen dealer, or.. 3D print them.
I spend quite some time measuring, CAD modelling and fast print test, so finally can say have something useful.
[Read More…]
Monday, 1-May-2017
Add dual fan system to 2.5W cnc laser
EN
Hello reader,
In that article wish to show and share one idea of mine for dual fan system (biturbo ha ha) for my cnc 2.5W laser. That is suitable with probably all hobby laser coolers using 30mm fans and aluminium profile 33×33 mm for cooling. So here we go:
[Read More…]
Saturday,22-April-2017
Woodpecker GRBL CNC Board - Firmware Update
EN
If you own CNC 2418 machine(like me), or just have Woodpecker GRBL CNC Board you can update to GRBL firmware v1.1.
But if you`re “lucky” like me,when try via Arduino IDE, you`ll hit into: “resp. = 0×0d” or similar compiler error. That is because the Atmel chip is without boot loader. Even with Xloader you`ll hit the wall. So then what?
[Read More…]
Friday,14-April-2017
Jetta 1K2 - immo problem [solved]
EN
Have to admit - sometimes VW make really good puzzles for solving with their documents. This time the car that will talk about is Jetta model 2006. 1.6 FSI with average equipment.
The problem was that after visit to service the car suddenly lost central lock. Dealer conclusion was: you need new set of keys and front doors lock motors replaced. Well…
[Read More…]
Lenovo K910 power cable fix
EN
Lenovo K910 - not that bad phone, but the owner of that Chinese marvel grumble that in few days it did charge only from time to time, and when move the power supply cable sometimes it work sometimes not.
From ebay was ordered new ribbon cable and here how it goes..
[Read More…]
Sunday,26-March-2017
miniCNC & 3D printer
EN
Good day folks,
Recently I bought myself 3D printer (da Vinci Mini WiFi) and mini CNC 2418 router / laser all in one.
da Vinci
Sunday, 5-February-2017
TURBOX notebook power supply fix
EN
That article is about mate`s notebook TURBOX which didn`t start. Simple device based on INTEL processor. As you can see from the pictures there are not so much “inwards” in that device. What I have is to check if it start on battery - NO. Power plug on place - nobody. To get access to the mainboard power points I have to remove the keyboard.
[Read More…]
Xantia Estate - trunk light improvement
BG На български тук: http://clubcitroen.bg/forum/viewtopic.php?f=181&t=71202&p=763447
EN
Hi folks,
Here is my improvement of my Xantia estate trunk light. First i bought COB led panels from ebay. The price including delivery is about 2-2.5$. That`s a deal ![]()
[Read More…]
Saturday,28-January-2017
Philips BT speaker / Sony amp / Nexus 7
EN
What is the story here:
Philips BT speaker: the small charging port-plug seems to have problem with it mainboard contacts. Thin solder iron tip, and job done. To open the speaker, remove the “sweater” , undo the bottom 3 screws and be careful with the small wires.
[Read More…]