Sunday,27-November-2016
Carisma 1.8 GDI - starting problem/solution
| EN | BG |
| Here, will not try to write full article how you can solve all starting issues with Mitsubishi Carisma 1.8 GDI. In fact, will be breef description what I have done to fix the problem in my case, which hope will be some how helpful to you also. |
Описаното тук няма за цел да направи статия за всички проблеми довеждащи до не стартиране двигателя на Митсубиши Каризма 1.8 GDI. Просто кратко описание на проблем който отстраних, и което може да Ви бъде от полза. |
[Read More…]
Friday,21-October-2016
Delonghi EC330S - how to open? :)
EN: In some point my coffee maker decide to rise some kind of work strike. It was something simple which will not bother you to read, but in case you wish to see how to open that device, here you go:
[Read More…]
Friday,30-September-2016
VDO Marelli Idle motor - test control
EN
Because I start to have some issues with my Xantia`s Idle motor decide to build something what can help me to move the valve piston IN and OUT and test it how it goes. In that way it will be easy to open and clean it, and of course to fit it back.
Used parts are:
Tuesday,20-September-2016
Xantia MkII 1999 - Cabin blower problem[fix]
BG: на български език можете да прочетете тук: http://www.clubcitr … 193&start=1002
EN:
There are quite many topics in forums and etc, that give ideas or guides how to fix xantia blower problems. My case unfortunately wasn`t in any of that. Hope my story will be helpful to some of you.
First to clear one thing for the protocol - only if engine is working (alternator signal to the A/C ECU) you can have blower ON.
[Read More…]
Saturday, 9-July-2016
Custom Otside Hexagon - Heidenhain Program
Тhat is my idea of custom HEXAGON creating program. You can change only 2 variables and make your hexagon. The program is demonstrated with end mill 10mm but you can use any size and the program will use Q108(tool offset radius) to calculate position.
[Read More…]
Passat B6 V158 motor fix/replacement
| EN | BG |
| In that topic will try to explain what you can do to try fixing or replace your dead/not working V158 flap motor | В тази тема, ще опитам да поместя малко информация как да се справите с проблемно моторче на клапа наречено V158 |
Sunday,15-May-2016
Xantia Mk2 Instrument Panel Backlight Bluetooth controlled
BG Описано на български: тук
EN Hi,
In that topic will try to describe one idea for my Xantia instrument cluster back-light, but it can be used/set to any other car or to be used for other project as well.
Parts been used : WS2812B LEDs , Arduino Nano, HC-06 serial(with board) and some small electronic elements.
But before start any proper description, let me say that all credits goes to: josh.com Without his clean and simple code that will be bad going project, or lets say with Adafruit library it come little overweight.
Electrical diagram is like that:[Read More…]
Monday, 4-April-2016
VW Touran 2003 1.9TDI - Wiper motors fix / проблем с чистачки[решение]
| EN | BG |
| Well, the title is not exactly match of the real story, I did not fix the electronic in the motor, but hope when you get to the end of that article, you`ll be one idea more prepared what to check and expect if you get in that situation. Before even to begin will presume you have checked Fuses and Relays for some problem and we`re sure all that should work. So, the owner of the car get firstly passenger motor failure. Just to mention that here I speak for EU driving position not UK or JP. The diagnostic program(VCDS) pull the error and show it. Later on, that motor was replaced but quite soon after the wipers went dead again. And if you try look in group [9] you`ll get that: | Всъщност,заглавието е малко подвеждащо(нямам за цел да описвам оправяне на моторите) но се надявам в края на написаното да имате една идея горница какво да проверите в лучай на аналогичен проблем. Преди да започна с описанието предполагам, че сте проверили вече релета и бушони и е сигурно че от към този фронт нещата са наред. Собственикът на колата спомена първо е излизала грешка свързана с мотора на пасажерското място. Това отнасящо се към еропейските версии не UK, или Япония. Моторът е бил подменен с такъв от морга, но след това всякаква връзка с чистачките изчезнала, както и работещото им състояние. Тоест, останала да работи само задната. |
[Read More…]
Saturday, 2-April-2016
Heidenhain - hardware limit
EN What will happen when the software limit is not set right?
Here is the case - SET at:
[Read More…]
Heidenhain NC - spindle or axis power indicator
EN If you use machine with Heidenhain NC probably have seen that small line that shows Feed and Spindle power.
[Read More…]
